Cat Dozers:

D6T Track-Type Tractor

Engine Model
Cat C9.3 ACERT™
Flywheel Power
215 hp
Operating Weight
47138 lb
Displacement
567 in3

The new D6T dozer makes high efficiency dozing as easy as driving your pickup truck. A smooth-shifting, fully automatic four-speed Cat® transmission continuously optimizes the power train for the application. You save fuel and operator effort, without sacrificing durability, power or productivity. Work smarter too, with a full range of Cat Connect GRADE technology features to fit your job site needs.



Product Specs

  • Engine

  • Engine Model
    Cat C9.3 ACERT™
    Flywheel Power
    215hp
    Displacement
    567in3
    Net Power (Maximum) – 1,200 rpm: ISO 9249/SAE J1349
    245hp
    Emissions
    U.S. EPA Tier 4 Final
    Net Power (Rated) – 2,200 rpm: ISO 9249/SAE J1349
    215hp
    Note
    All non road Tier 4 diesel engines are required to use only Ultra Low Sulfur Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less. Biodiesel blends up to B20 (20% blend by volume) are acceptable when blended with 15 ppm (mg/kg) sulfur or less ULSD
    Note
    Diesel Exhaust Fluid (DEF) used in Cat Selective Catalytic Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241.
    Build Number
    19
  • Weights

  • Operating Weight
    47138lb
  • Service Refill Capacities

  • Fuel Tank
    97.2gal
    Cooling System
    12.2gal
    Engine Crankcase
    6.5gal
    Power Train
    39.1gal
    Final Drives (each)
    3.6gal
    Hydraulic Tank
    16.5gal
    DEF Tank
    4.5gal
    Roller Frames (each)
    6.6gal
    Pivot Shaft Compartment
    1.3gal
  • Operating Weight

  • XL A
    47846lb
    XL SU
    47138lb
    XL VPAT
    53042lb
    XW A
    49797lb
    XW SU
    48909lb
    XW VPAT
    54045lb
    LGP S
    51385lb
    LGP A
    53829lb
    LGP VPAT
    54526lb
    Note
    Operating weight includes blade, lubricants, coolant, full fuel tank, standard track, ROPS/FOPS cab, drawbar and operator.
  • Blades – Capacity

  • XL SU-Blade
    7.26yd3
    XL A-Blade
    5.17yd3
    XL VPAT-Blade
    6.07yd3
    XW SU-Blade
    7.38yd3
    XW A-Blade
    5.69yd3
    XW VPAT-Blade
    6.57yd3
    LGP S-Blade
    4.96yd3
    LGP A-Blade
    6.46yd3
    LGP VPAT-Blade
    6.57yd3
  • Dimensions – XL

  • Width of Tractor Without Trunnions (standard track)
    8.00ft
    Machine Height to Product Link Antenna(1)
    10.67ft
    Length of Track on Ground
    9.25ft
    Length of Basic Tractor(2)
    13.83ft
    Ground Clearance
    15in
    Ground Pressure (ISO 16754)(3)
    8.66psi
    Note
    (1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
    Note
    (2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
    Note
    (3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.
  • Dimensions – XW

  • Width of Tractor Without Trunnions (standard track)
    9.17ft
    Machine Height to Product Link Antenna(1)
    10.67ft
    Length of Track on Ground
    9.25ft
    Length of Basic Tractor(2)
    13.83ft
    Ground Clearance
    15in
    Ground Pressure (ISO 16754)(3)
    6.64psi
    Note
    (1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
    Note
    (2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
    Note
    (3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.
  • Dimensions – LGP

  • Width of Tractor Without Trunnions (standard track)
    10.50ft
    Machine Height to Product Link Antenna(1)
    10.83ft
    Length of Track on Ground
    10.67ft
    Length of Basic Tractor(2)
    14.50ft
    Ground Clearance
    16in
    Ground Pressure (ISO 16754)(3)
    5.11psi
    Note
    (1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
    Note
    (2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
    Note
    (3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.
  • Dimensions – XL VPAT

  • Width of Tractor Without Trunnions (standard track)
    8.92ft
    Machine Height to Product Link Antenna(1)
    10.67ft
    Length of Track on Ground
    9.25ft
    Length of Basic Tractor(2)
    16.08ft
    Ground Clearance
    15in
    Ground Pressure (ISO 16754)(3)
    9.78psi
    Note
    (1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
    Note
    (2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
    Note
    (3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.
  • Blades – Width

  • XL SU-Blade
    10.7ft
    XL A-Blade
    13.7ft
    XL VPAT-Blade
    12.7ft
    XW SU-Blade
    11.7ft
    XW A-Blade
    14.8ft
    XW VPAT-Blade
    13.7ft
    LGP S-Blade
    13.3ft
    LGP A-Blade
    16.6ft
    LGP VPAT-Blade
    13.7ft
  • Dimensions – XW VPAT

  • Width of Tractor Without Trunnions (standard track)
    9.83ft
    Machine Height to Product Link Antenna(1)
    10.83ft
    Length of Track on Ground
    10.67ft
    Length of Basic Tractor(2)
    16.42ft
    Ground Clearance
    16in
    Ground Pressure (ISO 16754)(3)
    6.92psi
    Note
    (1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
    Note
    (2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
    Note
    (3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.
  • Dimensions – LGP VPAT

  • Width of Tractor Without Trunnions (standard track)
    10.33ft
    Machine Height to Product Link Antenna(1)
    10.83ft
    Length of Track on Ground
    10.67ft
    Length of Basic Tractor(2)
    16.42ft
    Ground Clearance
    16in
    Ground Pressure (ISO 16754)(3)
    6.28psi
    Note
    (1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
    Note
    (2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
    Note
    (3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.

Request a Quote

Please leave this field empty.

Find a Walker CAT
Location or Rep Near You